| 本文已被：浏览 699次 下载 435次 |
码上扫一扫！ |
| 奶牛喷淋降温水滴形态特性的数值模拟 |
|
张驰也1,2, 陈洋1,2, 施正香1, 丁涛1, 宏帅1,2, 方露梦1,2
|
|
|
| (1.中国农业大学 水利与土木工程学院/农业部设施农业工程重点实验室, 北京 100083;2.北京市供水管网与安全节能中心, 北京 100083) |
|
| 摘要: |
| 为研究奶牛喷淋降温过程中的水滴形态特性，以及水滴撞击壁面过程中的铺展系数与水滴喷淋速度和接触角之间的关系问题，采用CLSVOF数值模拟方法，对单个水滴与固体壁面撞击过程进行三维数值模拟。首先根据Yokoi的试验对本研究数值模型的准确性进行验证，然后根据本研究试验测试数据建立数值模型，同时结合韦伯数（We）、雷诺数（Re）及系数K对数值模型进行分析验证。研究了水滴粒径分别在0.5和0.8 mm条件下：当速度分别以1、2和3 m/s，平均接触角为120°时水滴撞击固体壁面时的形态变化；当接触角分别为90°、120°和140°，速度为1 m/s时水滴撞击固体壁面时的形态变化。结果表明：随液滴直径和撞击速度的增加，液滴撞击壁面后主要有振荡、反弹、破碎和飞溅这4种典型运动形态；随着水滴速度的增大，水滴铺展速度加快，最大铺展直径与铺展系数增大；随着接触角增大，水滴最大铺展直径减小，最大铺展系数值减小。 |
| 关键词: CLSVOF 水滴形态 奶牛喷淋 接触角 水滴速度 |
| DOI：10.11841/j.issn.1007-4333.2018.08.09 |
| 投稿时间：2017-10-18 |
| 基金项目:国家自然科学基金项目（31402115）；国家奶牛产业技术体系项目（CARS-37）；国家级大学生创新性计划（201610019072） |
|
| Study on morphological characteristics of sprayed water drop by numerical simulation |
|
ZHANG Chiye1,2, CHEN Yang1,2, SHI Zhengxiang1, DING Tao1, HONG Shuai1,2, FANG Lumeng1,2
|
| (1.College of Water Resources and Civil Engineering/Key Laboratory of Agricultural Engineering in Structure and Environment, China Agricultural University, Beijing 100083, China;2.Beijing Engineering Research Center of Safety and Energy Saving Technology for Water Supply Network System, Beijing 100083, China) |
| Abstract: |
| In order to study the droplet morphological characteristics of cow during the spray cooling process,and the relationship between spread coefficient and droplet spraying velocity and contact angle in the process of water drop hitting the wall,a three-dimensional numerical simulation of the collision between a single droplet and the solid wall was carried out by using the CLSVOF numerical simulation method.First of all,based on the experimental test reported by Yokoi,this study verified the accuracy of the numerical model in this study.Then,based on the experimental data,a numerical model was established.Combined with Weber number (We),Reynolds number (Re) and coefficient K,the numerical model is validated.Morphological changes during the process of water droplets hitting solid wall were studied at 2 droplet diameter of 0.5 and 0.8 mm:Firstly,the velocity of 1,2 and 3 m/s,the average contact angle of 120° respectively;Secondly,the contact angles of 90°,120° and 140°,the velocity of 1 m/s respectively.The results showed that:With the increase of droplet diameter and impact velocity,there were 4 typical forms of motion after the droplet hitting wall including oscillation,bounce,breaking,splashing;With the increase of water droplet velocity,the spreading velocity of water droplets accelerated,the maximum spreading diameter and spread coefficient increased at the same time;With the increase of contact angle,the maximum spreading diameter of water droplets decreased and the maximum spreading coefficient decreased. |
| Key words: CLSVOF droplet morphology dairy sprinkler contact angle water droplet velocity |
